镁/铝层状复合材料的扩散连接制备及界面特性

谭成文; 李珊珊; 周终强; 郑秀华; 王富耻; 才鸿年

专利文献信息 | 浏览量 : 0 下载量: 797 CSCD: 5

导出
分享
收藏
专辑

镁/铝层状复合材料的扩散连接制备及界面特性
Fabrication of Magnesium/aluminum Laminated Composites by Diffusion Bonding and Its Interface Properties
2007年第1期页码：1-3
纸质出版日期： 2007 ，
DOI：

扫描看全文

[1]谭成文,李珊珊,周终强,郑秀华,王富耻,才鸿年.镁/铝层状复合材料的扩散连接制备及界面特性[J].特种铸造及有色合金,2007(01):1-3+7.

Tan Chengwen~ 1, Li Shanshan~1, Zhou Zhongqiang~1, et al. Fabrication of Magnesium/aluminum Laminated Composites by Diffusion Bonding and Its Interface Properties[J]. Special Casting & Nonferrous Alloys, 2007,(1):1-3.
[1]谭成文,李珊珊,周终强,郑秀华,王富耻,才鸿年.镁/铝层状复合材料的扩散连接制备及界面特性[J].特种铸造及有色合金,2007(01):1-3+7. DOI：

Tan Chengwen~ 1, Li Shanshan~1, Zhou Zhongqiang~1, et al. Fabrication of Magnesium/aluminum Laminated Composites by Diffusion Bonding and Its Interface Properties[J]. Special Casting & Nonferrous Alloys, 2007,(1):1-3. DOI：

摘要

采用扩散连接制备了镁/铝层状复合材料

进而采用热处理改善界面结合性能

最后利用纳米压痕技术初步研究了复合材料的界面结合状况。结果表明

采用400℃/30MPa/10min、400℃/40MPa/10min和400℃/30MPa/20min3种条件均可获得连接较好的层状复合材料

但400℃/30MPa/10min条件下扩散层不明显;利用热处理可以改善界面结合状况

对于扩散层明显的复合材料

热处理可以大大增加扩散层厚度;扩散层的纳米硬度比基体高约3倍

弹性模量介于镁合金的与铝合金的之间。

Abstract

Magnesium/aluminum laminated composites were fabricated by diffusion bonding method

and interfacial characteristics were measured by nano-indentation to know how to improve the interfacial properties of heat treated composites.The results reveal that laminated composites with desirable bonding can be prepared by the diffusion bonding with three sets of processing parameters

including 400 ℃/30 MPa/10 min

400 ℃ /40 MPa/10 min

400 ℃/30 MPa/20 min

however

the diffusion layer is not visible in the condiions of 400 ℃/30 MPa/10 min.Diffusion layer thickness of the composites can be remarkably increased with heat treatment

and nano-hardness of diffusion zone is 3 times higher than that of the matrix

and the Young’s modulus is located in the range of that of magnesium alloy and aluminum alloy.